Vehicle Equipment & Wiring Diagrams

Download the documents below for further support regarding vehicle installations for all [http://www.gpslogic.net|GPS Logic] supported hard mount modems.

'''Note: ''' Use the pictures at the right of each section to identity your specific modem.

{toc}

===1 - Modems===

Installation diagrams for GPS enabled modems.  All modems support 12 to 24V electrical systems with negative ground.

====1.1 - Sierra Wireless AirLink Modems====
Configuration and installation instructions for Sierra Wireless AirLink modems including the Pinpoint, Raven, and GX400 series modems. Additional documents may be found at [http://www.sierrawireless.com]

* [Sierra-Wireless-Modem-Configuration-AirLink-series|Configuration Instructions] - '''This process must be completed for each modem to be used with the GPS Logic system.'''


====1.2 - Logic-5000====

<table width="100%"><tr><td valign="top">
Installation diagrams, manual, and instructions for the Logic-5000 mobile cellular router.
* [{UP}/docs/logic-5000/manuals/Logic-5000 Manual (CDMA) Ver 3.2.2.pdf|User Manual]
* [{UP}/docs/example_network_config.pdf|Example Network Diagram]
* Wiring Diagrams
** [{UP}/docs/Logic-5000_basic_install.pdf|Basic Installation Diagram]
** [{UP}/docs/logic-5000/L-5000_gforce.pdf|G-Force Sensor Mounting & Wiring]
** [{UP}/docs/logic-5000/L-5000_pinout.pdf|I/O Connector Pin-Out]
** [{UP}/docs/logic-5000/L-5000_code3.pdf|Lightbar & Code-3 Monitoring]
** [{UP}/docs/logic-5000/L-5000_unlock.pdf|Remote Unlock (Generic)]
** [{UP}/docs/sprinter_unlock.pdf|Dodge Sprinter Lock/Unlock Connections]
** Garmin Messaging
*** [{UP}/docs/logic-5000/L-5000_garmin.pdf|Garmin Power Options]
*** [{UP}/docs/logic-5000/fmi40-Logic5000.pdf|Data Interface Cable (FMI-40) Pinout]
* Antenna Installation
** [{UP}/docs/Antenna Configuration.pdf|Antenna Placement Diagram]
** [{UP}/docs/AntennaMounting.pdf|Antenna Mounting]
* Device Configuration
** [DefaultL-5000Config|Restoring Defaults]
** [L-5000ConfigPage|Using with GPS Logic Fleet Management System]
* Road Safety Integration
** [{UP}/docs/roadsafety/Road Safety Interface - External Module.pdf|Road Safety Interface Module (External)] - Use only when Logic-5000 COM port is already in use.
* Firmware Upgrade (<b>Logic-5000 Only</b>)
** [{UP}/firmware/Logic-5000_Firmware_Update.pdf|Firmware Upgrade Instructions]
** [{UP}/firmware/3.2.1/upgrade.tar.gz|Version 3.2.1 Upgrade File] - Use only for upgrading from versions 3.x.x.  Do NOT use for devices with version 4.0.0 or higher firmware.
** [{UP}/firmware/4.0.9/upgrade.tar.gz|Version 4.0.9 Upgrade File] - Use only for upgrading from version 4.0 or higher.  Do NOT use for devices with version 3.x.x.
** [{UP}/logic5000/cellfix/upgrade.tar.gz|Cell Connectivity Patch] - Use only for patching firmware versions 4.0 or higher. This patch will correct cellular connectivity issues on the Logic-5000. Does not change firmware version number.
* [Flash-Recovery|Flash Recovery of Logic-5000] - Use to recover device when it won't boot

(((
'''Power Cable Color Coding'''

* '''Red''' - Hot at all times.  Do ''NOT'' connect to switched power.  Device can be configured via internal web interface to shut off on timer or low voltage conditions.
* '''White''' - Ignition.  Avoid connecting to vehicle's accessory line when possible.
* '''Blue''' - Vehicle ground.

)))

</td><td>[imageright|Logic-5000 Mobile Cellular Gateway/Router|{UP}/img/Vanguard_th.png]</td></tr></table>


====1.3 - Logic-4200====

<table width="100%"><tr><td valign="top">
Installation diagrams specific to the Logic-4200 modem.

* [{UP}/docs/4200_Amb_Garmin.pdf|Ambulance Wiring Diagram (with Garmin Option)]
* [{UP}/docs/4200_wiring.pdf|Pin-out Reference]
* [{UP}/docs/lmu_generic_unlock.pdf|Generic Remote Unlock]
* [{UP}/docs/sprinter_unlock.pdf|Dodge Sprinter Remote Unlock Connections]
* [{UP}/docs/AntennaMounting.pdf|Antenna Mounting (Combination Cellular + GPS Antenna)]
* [{UP}/docs/fmi-40.pdf|FMI-40 Cable] (For installations with interfaced Garmin navigation devices)

(((
'''Power Cable Color Coding'''

* '''Red''' - Hot at all times.  Do ''NOT'' connect to switched power.  Device can be configured to shut off on timer or low voltage conditions.
* '''White''' - Ignition.  Avoid connecting to vehicle's accessory line when possible.
* '''Green''' - Analog input 1.  Typically left disconnected and insulated from other wires and connections.
* '''Black''' - Vehicle ground.

)))

</td><td>[imageright|Logic-4200 Location & Messaging Unit|{UP}/img/lmu4200_th.png]</td></tr></table>

====1.4 - Logic 2500/2600====

<table width="100%"><tr><td valign="top">
Installation diagrams for the Logic 2500/2600 modems.

* [{UP}/docs/2500_garmin.pdf|Garmin Wiring]
* [{UP}/docs/2500_wiring_amb.pdf|Wiring Diagram (Ambulance Specific)]
* [{UP}/docs/2500_wiring_tow.pdf|Wiring Diagram (Tow Specific)]
* [{UP}/docs/2600_temp.pdf|Wiring Diagram (Digital Temperature Monitoring)]
* [{UP}/docs/lmu_generic_unlock.pdf|Generic Unlock]
* [{UP}/docs/sprinter_unlock.pdf|Dodge Sprinter Remote Unlock Module Installation]

(((
'''Power Cable Color Coding''' - See wiring diagrams above for detailed instructions.

* '''Red''' - Hot at all times.  Do ''NOT'' connect to switched power.  Device can be configured to shut off on timer or low voltage conditions.
* '''White''' - Ignition.  Avoid connecting to vehicle's accessory line when possible.
* '''Black''' - Vehicle ground.

)))

</td><td>[imageright|Logic 2500/2600 Tracking & Messaging Unit.|{UP}/img/lmu2500_th.png]</td></tr></table>


====1.5 - Navman Qube 2 (Legacy)====

<table width="100%"><tr><td valign="top">
Programming Software
* [{UP}/docs/cube/Cube Programming Instructions.pdf|Programming Instructions]
* [{UP}/firmware/cube/QubeProgramming.zip|GPS Logic Firmware]
* [{UP}/drivers/PL2303_Prolific_DriverInstaller_v1.6.0.zip|USB to Serial Cable Drivers] (PL-2303 chipset)

(((
'''DB9 to RJ45 Pinout for Programming Dongle'''
* Blue - Pin 5
* Green - Pin 2
* Red - Pin 3
)))

Installation diagrams for Navman Qube 2 modems (GPRS).

* [{UP}/docs/cube/Qube_2_Install_Manual.pdf|Manufacturer Installation Guide]
* [{UP}/docs/cube/Qube_Amb.pdf|Wiring Diagram (Ambulance Specific)]
* [{UP}/docs/cube/Qube_Tow.pdf|Wiring Diagram (Tow Specific)]
* [{UP}/docs/cube/Qube_Temp.pdf|Wiring Diagram (Analogue Temperature Monitoring)]

(((
'''Power Cable Color Coding''' - See wiring diagrams above for detailed instructions.

* '''Red''' - Hot at all times.  Do ''NOT'' connect to switched power.  Device can be configured to shut off on timer or low voltage conditions.
* '''Pink''' - Ignition.  Avoid connecting to vehicle's accessory line when possible.
* '''Yellow''' - Input 1.  Typically connected to code-3 signal on emergency vehicles, or PTO on tow and utility vehicles.
* '''Black''' - Vehicle ground.

)))

</td><td>[imageright|Qube 2 Tracking Unit.|{UP}/img/qube2_th.png]</td></tr></table>



===2 - Bluetooth Access Point===

The following instructions indicate how to configure the Bluetooth Access Point as a Personal Area Network (PAN) for connecting cardiac monitors, PDAs, tablet PCs, or other internet connected devices.  '''Note:''' The Bluetooth Access Point is supported only with the Logic-5000 (formerly the Vanguard).

* [BluetoothConfigPage|Bluetooth Access Point Configuration]


===3 - Navigation & MDT Installation===

Installation diagrams for MDT-860s and Garmin navigation units.


====3.1 - Garmin Navigation Installation====

To connect a supported Garmin navigation device to your modem equipment for text messaging and navigation, connect the FMI-40 cable (available from GPS Logic) to your modem's DB-9 serial connector.

If the FMI-40 cable does not include a DB-9F connector, use the following pin-out to add one.

@@
Garmin FMI-40 Wiring (All modems except Logic-5000)
- Brown: Pin 5
- Yellow: Pin 2
- White: Pin 3

Garmin FMI-40 Wiring (Logic-5000 ONLY)
- Brown: Pin 5
- Yellow: Pin 3
- White: Pin 2
@@

[{UP}/docs/fmi-40.pdf|FMI-40 Cable Diagram (For installations with Garmin nav units)]

To test an FMI-40 cable, connect it to your computer's serial port and run the FMI Utility application: [{UP}/tools/FMI-Test.exe|FMI-Test.exe]


====3.2 - MDT-860 Installation====

* [{UP}/docs/Modem_Install_with_Nav.pdf|Modem Installation with Navigation & MDT/Status Head]


===4 - Vehicles===

Vehicle manufacturer wiring diagrams are for informational purposes only.  Although specifications may be similar, variations are common.  Connections to manufacturer's equipment should be tested and verified by qualified personnel.

====4.1 - Leader Ambulance====

* [{UP}/docs/amb_manufacturers/LeaderVans04-2008.pdf|Leader Van Chassis]{br}
* [{UP}/docs/amb_manufacturers/LeaderMods04-2008.pdf|Leader Modular Chassis]

====4.2 - Ford E-Series Van====

Refer to the color-coding information in section 1 of this page.  If used, the door unlock output line must be connected to an active low unlock trigger.  On vehicles with factory alarms, this is typically the pink/green wire located behind the driver side kick-panel (next to the parking brake).

{cloud}
Meta Keywords: diagram, installation, manual, modem, vehicle, wiring
Meta Description: Installation diagrams and user manuals for GPS Logic modems.
Change Comment: